Better Wetting and Hole Fill<\/h2>\n\n\n\n Nitrogen does not improve soldering by directly changing the solder alloy. It improves the conditions in which the solder and flux work.<\/p>\n\n\n\n
With less oxide forming on the molten solder surface, solder can wet the pad and component lead more consistently. This can improve capillary flow through plated holes and help achieve the required hole fill, especially with lead-free alloys, large connectors or PCBAs with greater thermal mass.<\/p>\n\n\n\n
Nitrogen cannot compensate for a contaminated pad, poor component solderability, an unsuitable nozzle or insufficient contact time. These conditions must still be corrected through the soldering programme and material selection.<\/p>\n\n\n\n
More Stable Drainage and Less Bridging<\/h2>\n\n\n\n The point where the PCBA leaves the mini-wave is particularly important. Solder must drain cleanly away from the joint without leaving a bridge or icicle.<\/p>\n\n\n\n
Oxide on the solder surface can disturb this separation. By displacing oxygen around the nozzle and separation area, nitrogen supports cleaner solder drainage and can reduce bridging, spikes and solder flags.<\/p>\n\n\n\n
Fine-pitch connectors can benefit from this wider process window, but withdrawal direction, nozzle size, solder height and movement speed remain equally important.<\/p>\n\n\n\n
Less Dross and Better Nozzle Protection<\/h2>\n\n\n\n Solder dross forms when molten solder oxidizes. Excessive dross consumes solder, contaminates the solder-pot surface and increases maintenance around the pump and nozzle.<\/p>\n\n\n\n
Nitrogen limits contact between oxygen and the molten solder. This reduces dross formation and helps the mini-wave maintain a cleaner, more stable surface.<\/p>\n\n\n\n
The nozzle also benefits from reduced oxidation. Oxide buildup can interfere with nozzle wetting, change the wave shape and eventually reduce the effective solder height.<\/p>\n\n\n\n
Depending on its size, shape and supplier, a replacement selective soldering nozzle may cost approximately US$100\u2013300<\/strong>. Most factories also keep several nozzle sizes for different PCBAs. Protecting the nozzles therefore reduces both replacement expense and the risk of production interruption.<\/p>\n\n\n\nNitrogen does not make the nozzle maintenance-free. Operators must still inspect the opening, remove deposits, maintain nozzle wetting and confirm the wave height.<\/p>\n\n\n\nHeated Nitrogen and Flux Preheating<\/h2>\n\n\n\n Many selective soldering systems heat the nitrogen before it reaches the nozzle area. Heated nitrogen prevents cold gas from cooling the mini-wave and can provide additional local heat to the fluxed soldering area.<\/p>\n\n\n\n
Preheating helps evaporate flux solvent before the PCBA contacts molten solder. If excessive liquid flux, solvent or moisture reaches the mini-wave, it can generate solder spatter and disturb the wave.<\/p>\n\n\n\n
Heated nitrogen can reduce this risk by supporting local preheating, but it does not guarantee that spattering will disappear. Flux quantity, board temperature, preheating time and moisture must still be controlled.<\/p>\n\n\n\n
For PCBAs with high thermal mass, dedicated infrared or convection preheating may still be required.<\/p>\n\n\n\n
Nitrogen Parameters That Matter<\/h2>\n\n\n\n A high flow rate alone does not produce a stable nitrogen atmosphere. Purity, flow, pressure, temperature and leakage must work together.<\/p>\n\n\n\nProcess parameter<\/th> Why it matters<\/th> If it is unstable<\/th><\/tr><\/thead> Nitrogen purity<\/td> Determines how much oxygen enters with the supplied gas<\/td> More oxidation and dross may form<\/td><\/tr> Flow rate<\/td> Displaces air around the nozzle and soldering area<\/td> Low flow allows surrounding air to enter<\/td><\/tr> Inlet pressure<\/td> Maintains the required gas supply through the machine<\/td> Pressure loss can change the protective atmosphere<\/td><\/tr> Nitrogen temperature<\/td> Prevents cold gas from cooling the solder wave<\/td> Unheated gas may reduce local thermal stability<\/td><\/tr> Pipe and enclosure sealing<\/td> Prevents unnecessary mixing with factory air<\/td> Leakage raises oxygen content and gas consumption<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\nThe purity stated by the nitrogen source is not always the oxygen condition at the solder joint. Nitrogen mixes with surrounding air as it leaves the nozzle, so the effective atmosphere also depends on nozzle design, flow direction, enclosure and leakage.<\/p>\n\n\n\n
For demanding applications, oxygen should be evaluated close to the actual soldering area rather than relying only on the purity displayed by the nitrogen generator.<\/p>\n\n\n\n
Nitrogen Requirements for a DEZ Selective Soldering Machine<\/h2>\n\n\n\n The DEZ-H3500A automatic selective soldering machine<\/a> uses nitrogen around its mini-wave nozzle to limit oxidation and support solder wetting.<\/p>\n\n\n\nIts current specification requires nitrogen purity above 99.998%<\/strong>, an inlet pressure of 3\u20134 bar<\/strong> and consumption of approximately 1\u20132 m\u00b3\/h per operating nozzle<\/strong>.<\/p>\n\n\n\nThese values apply to the H3500A configuration. Other machines may have different nozzle quantities, flow requirements or operating pressures, so nitrogen supply should be confirmed from the selected model rather than copied between machines.<\/p>\n\n\n\n
Nitrogen Generator or Cylinders?<\/h2>\n\n\n\n Nitrogen cylinders can be practical for occasional soldering, process trials or emergency backup. Regular production requires repeated cylinder ordering, storage and replacement, creating a risk of interruption when a cylinder becomes empty.<\/p>\n\n\n\n
An on-site nitrogen generator produces nitrogen continuously from clean, dry compressed air. It is normally more practical when selective soldering machines operate frequently or across multiple shifts.<\/p>\n\n\n\n
The DEZ-D59-2N SMT nitrogen generator<\/a> provides a standard output of 3 Nm\u00b3\/h<\/strong>, purity up to 99.999%<\/strong> and adjustable pressure from 0.1 to 0.65 MPa<\/strong>.<\/p>\n\n\n\nBefore connecting it to a soldering machine, compare its output with the machine\u2019s combined continuous and peak demand. Pipe losses, additional machines and future production expansion must also be considered.<\/p>\n\n\n\nNitrogen Does Not Replace Process Control<\/h2>\n\n\n\n Nitrogen widens the selective soldering process window, but it cannot correct an unsuitable solder alloy, excessive flux, poor preheating or an incorrectly selected nozzle.<\/p>\n\n\n\n
Void or gas-pocket formation should not be treated as a nitrogen-only problem. Flux quantity, solvent evaporation, hole geometry, solderability, contact time and solder drainage must also be evaluated.<\/p>\n\n\n\n
A stable process therefore combines the correct nitrogen atmosphere with controlled fluxing, preheating, solder temperature, wave height, contact time and withdrawal direction.<\/p>\n\n\n\n
Send DEZ your selective soldering machine model, number of solder pots and nozzles, required nitrogen purity, operating pressure, continuous consumption and daily working hours.<\/p>\n\n\n